Dual 36” x 10’ – Vertical Test separator package- 1440 PSIG

**3 units available - 2 of which do not yet have the meter runs.  Additional $14K to add the meter run (per pkg).

• Alberta & BC registered.
• Vessel is RT-1 / 1/8” C.A. / PWHT.
• Sour service – fully flanged
• (2)  4” Sr. Meter run. – Daniel
• (2) BPCV - 3” – Fisher ET valve
   
• Both vessels are Dressed 3 phase.
• (4) LCV- 2” Fisher D4 – c/w 1 ¼” Tungsten trim
• (2) LIT – Rosemount 5302 Guide Wave Radar
• (4) Sur-flo – 2” x 1 ½” Turbines. c/w MC III Totalizer.                 
• Level switches – Rosemount 2120 Vibrating forks.
• PIT – Rosemount 2088 Transmitters
• WKM Ball valves
• Double doors.
• Exhaust fans

Please refer to supporting documents for additional info

3rd phase to be added (1-2 weeks to complete)

Principal Vessel Connections

• 6” 600# Inlet c/w 3” elbow diverter
• 6” 600# Gas out connection
• 2” 600# Water out connection
• 2” 600# Condensate out connection
• 2” 600# Drain connection
• 2 – 3” 600# LC connections
• 2” 600# PSV connection
• 3” 600# HLSD connection
• 3” 600# Inspection
• 4 – 2” 600# LG connections
• 2” 600# PI connection
• 2” 600# TI connection
• Internal float shield
• 6”x9#/cu. Ft. Demister pad

Please see supporting documents for more details.

• Constructed to ASME Section VIII Div I, with CRN Registered in Alberta, B.C.,
• Saskatchewan
• “U” Stamped
• 1/8” Corrosion Allowance
• 100°F Design Temperature
• M.D.M.T.-20°F @ 1440 Psig
• Inlet Diverter, Float Shield
• 6” Thick x 9 lb/ft3 Mistex
• Designed 3 Phase, Dressed 2 Phase

One 36” O.D. x 7’6” S/S x 1440# D.P.

1/8” Corrosion Allowance @ -20/100 Deg. F, 3 Phase Vertical Separator constructed to ASME code Section VIII Div. I., RT1 X-Ray & stress relieved

Comes complete with Accompanying MCC Building 800AMP 

Full sour, pipe & vessel. No T.O.L’s on pipe or vessel. 

BPCV & bypass flow line on sales gas from vessel.

Micro Motion fluid measurement.

HazLoc electric heater.

2 exhaust fans, 1 in roof eave, 1 at floor level.

Gas & H2S detection.

Wired to J.B.’s.

Eagle, 3 throw/single stage air comp.

Pig launcher outside.

Internall Coated Devoe 259

1) DC powered light

1) cata-dyne

2) chemical pumps

1) fuel gas scrubber

1) solar panel & battery

Process Building

304L Internally Clad

Constructed with Alberta, Sask, & BC Registration
100°F design temperature
Inlet diverter and float hood
4” thick x 9 lb/ft3 mistex
Radiography: RT-1,
Designed 3 phase/Dressed 2
Fully Flanged vessel

VESSEL CONNECTIONS:
N1 Gas Inlet 1 - 3” NPS 600 ansi Flange
N2 Gas Outlet 1 - 3” NPS 600 ansi Flange
C1 Drain 1 - 2” NPS 600 ansi Flange
C2 Condensate LLC 1 - 2” NPS 600 ansi Flange
C3 Water LLC 1 - 2” NPS 600 ansi Flange
C4 Condensate Outlet 1 - 2” NPS 600 ansi Flange
C5 Water Outlet 1 - 2” NPS 600 ansi Flange
C6 a/b LG - Condensate 2 - 2” NPS 600 ansi Flange
C7 a/b LG - Water 2 - 2” NPS 600 ansi Flange
C8 PI 1 - 2” NPS 600 ansi Flange
C9 TI 1 - 2” NPS 600 ansi Flange
C10 PSV 1 - 2” NPS 600 ansi Flange
C11 Inspection 2 - 2” NPS 600 ansi Flange

SENIOR METER RUN C/W FLOW CONDITIONER
3” 600# Flanged outer ends, Sch 80
SOUR. Service trim
10% Radiography
Built to AGA 2000 Edition
One (1) - 1” 3000# T.O.L. and one (1) 3/4” 3000# T.O.L. downstream

4"600# inlet, 3"600# outlet

Custom finish E&I to your spec (2-3 weeks)

One (1) 16” Sweet Service

Built in 2004 by Stettler Oil and Gas

720PSI

Catadyne Heat w/ Start Cables

2” Meter Run

Fuel Gas Scrubber

Methanol Tank w/ Single Pump

Double Wall 200BBL Tank - Insulated

Fully flanged vessel with threaded piping.

It does have electric valves and controllers on the liquids not pneumatic.

With Water Boot

Last inspection - 2011.  Reports available upon request.

24" x 8' Horizontal Inlet Separator Package